The Linux Boot Process: From Power Button to Kernel(0xkato.xyz)
0xkato.xyz
The Linux Boot Process: From Power Button to Kernel
https://www.0xkato.xyz/linux-boot/
95 comments
firmwares are the real IoT nobody talks about that that actually happened. infinite little computers and code churning away from view. and not being updated.
next 'snowden leaks' will have that word on every page.
next 'snowden leaks' will have that word on every page.
at least from whatever's been published, a good chunk of NSA's tools exploit low level firmware bugs like this...
also wondering how great my Asrock firmware is vs. say the bog standard Lenovo (i assume Apple is the one company that's expended significant thought into locking this process down)
also wondering how great my Asrock firmware is vs. say the bog standard Lenovo (i assume Apple is the one company that's expended significant thought into locking this process down)
Worse is how little information exists on firmware or how development for firmware works.
Its certainly not something regularly taught in higher education.
Its certainly not something regularly taught in higher education.
In a past life I held the title Firmware Engineer. The day-to-day development process did not differ from subsequent positions as a Software Engineer. Write-Compile-Test-Repeat. Then put it up for review so your colleagues can skewer it, or, on rare occasion, offer considerate and thorough feedback.
Firmware development is indeed taught in higher education. But not under the name "Firmware". It will be an "embedded systems" course or series of courses. At least in my experience, those courses are run by the Electrical Engineering department and the average Computer Science student stays far away from them.
Firmware development is indeed taught in higher education. But not under the name "Firmware". It will be an "embedded systems" course or series of courses. At least in my experience, those courses are run by the Electrical Engineering department and the average Computer Science student stays far away from them.
How do you test stuff that's deployed to firmware? At least when it comes to normie software your Linux or Mac box resembles the server you deploy to. And you can close the distance quite a bit with Docker.
But firmware? Totally different. FreeRTOS does have a POSIX backend, which helps some. Maybe you can run it under a hardware emulator. But it seems like lots of the stuff you want to test isn't really testable from the perspective of what a typical dev knows.
A lot of firmware dev iteration seems to be build -> flash -> watch serial connection for debug prints.
But firmware? Totally different. FreeRTOS does have a POSIX backend, which helps some. Maybe you can run it under a hardware emulator. But it seems like lots of the stuff you want to test isn't really testable from the perspective of what a typical dev knows.
A lot of firmware dev iteration seems to be build -> flash -> watch serial connection for debug prints.
> A lot of firmware dev iteration seems to be build -> flash -> watch serial connection for debug prints.
Serial port? Maybe for the fancy folks. Us lunch-pail types would find an unused GPIO, blue-wire an LED, and blink out a code of your choosing.
Okay, I never actually had to blink an LED but it was in my bag of tricks. The real golden-ticket to debugging embedded devices was a development kit with JTAG. JTAG, coupled with expensive additional hardware and equally expensive software license, gave you a gdb-like interface for debug. Breakpoints, stack traces, all the good stuff you take for granted when working with Windows, Linux, or those ugly abominations we call web browsers.
Emulators were also a thing, especially if your product had a custom ASIC and you needed pre-silicon development. But I didn't use them a lot myself and it seemed like by the time you had your emulation environment setup, there was 1st gen silicon and a debug board sitting at your desk.
Serial port? Maybe for the fancy folks. Us lunch-pail types would find an unused GPIO, blue-wire an LED, and blink out a code of your choosing.
Okay, I never actually had to blink an LED but it was in my bag of tricks. The real golden-ticket to debugging embedded devices was a development kit with JTAG. JTAG, coupled with expensive additional hardware and equally expensive software license, gave you a gdb-like interface for debug. Breakpoints, stack traces, all the good stuff you take for granted when working with Windows, Linux, or those ugly abominations we call web browsers.
Emulators were also a thing, especially if your product had a custom ASIC and you needed pre-silicon development. But I didn't use them a lot myself and it seemed like by the time you had your emulation environment setup, there was 1st gen silicon and a debug board sitting at your desk.
I'm not a firmware dev but the one's I've seen working usually have all sorts of fancy test kits, debug instrumentation, Software (chip scope?), etc. to debug with, not just relying on print debugging.
Not to say it isn't a valid way to debug, but there are definately better options available.
Not to say it isn't a valid way to debug, but there are definately better options available.
As someone in the security field, who is currently in a security degree program...I have a major overlap with the EE and computer engineering degree requirements.
Iv dabbled in some basic MIPS assembly and some microcontroller programming but don't consider that as complicated as boot level firmware or say the firmware that controls complex stuff.
I view embedded as the closest I will ever get to actual hardware engineering and it shocks me how complex everything is.
Iv dabbled in some basic MIPS assembly and some microcontroller programming but don't consider that as complicated as boot level firmware or say the firmware that controls complex stuff.
I view embedded as the closest I will ever get to actual hardware engineering and it shocks me how complex everything is.
If you're curious go walk through the bootloaders of an embedded platform, they serve roughly the same role as firmware that implements UEFI on traditional x86 systems.
Example, start with bl1 (first stage boot loader) for a Rasberry Pi here:
https://github.com/raspberrypi/arm-trusted-firmware
The Pi's hardware (register map, etc) is well documented so it's a good way to learn this stuff.
Example, start with bl1 (first stage boot loader) for a Rasberry Pi here:
https://github.com/raspberrypi/arm-trusted-firmware
The Pi's hardware (register map, etc) is well documented so it's a good way to learn this stuff.
Maybe not on compsci? but when I did electronic engineering it was covered as part of our embedded systems course.
There’s quite a lot of info out there on UEFI, and tiano core is open source. I taught myself enough to implement a small game you had to solve to be able to boot your machine, for example :)
There’s quite a lot of info out there on UEFI, and tiano core is open source. I taught myself enough to implement a small game you had to solve to be able to boot your machine, for example :)
I'm currently trying to learn more about how the boot process works, specifically with UEFI. Yesterday I watched a video on how to program a UEFI bootloader so I was happy when I saw this article this morning.
The article jumps over so many steps and leaves out so many mechanics that I had to stop reading, because it just opened more and more questions without closing any. For example, right at the beginning:
> Right after reset the CPU jumps to a special address called the reset vector at 0xFFFFFFF0. Think of it as a permanent bookmark that says “start here.” There is room for almost nothing at that address, so manufacturers put a short jump there that passes control to the firmware on your motherboard.
What does that even mean? It jumps there means that it executed whatever is at that address, but it failed to explain how the instruction at that location is even put there in the first place.
Reading a little more I truly am confused for who this was even written. It seems you need a lot of prior knowledge to understand what the author talks about and then it also makes me wonder what additional information this article conveys if you already can fill in the gaps.
The article jumps over so many steps and leaves out so many mechanics that I had to stop reading, because it just opened more and more questions without closing any. For example, right at the beginning:
> Right after reset the CPU jumps to a special address called the reset vector at 0xFFFFFFF0. Think of it as a permanent bookmark that says “start here.” There is room for almost nothing at that address, so manufacturers put a short jump there that passes control to the firmware on your motherboard.
What does that even mean? It jumps there means that it executed whatever is at that address, but it failed to explain how the instruction at that location is even put there in the first place.
Reading a little more I truly am confused for who this was even written. It seems you need a lot of prior knowledge to understand what the author talks about and then it also makes me wonder what additional information this article conveys if you already can fill in the gaps.
You use the toggle switches on the front panel to set the address to the reset vector and the data to the jump instruction, press a button to load the jump instruction into that address in memory, the press a button to reset the CPU.
More seriously, at least for modern systems: the engineers who designed the computer created a memory map that defined which hardware can be found where. They simply ensured that the reset vector would point to an area of non-volatile memory that can be read directly (e.g. an EEPROM would work since you feed it an address and it returns data, much like RAM). That jump would be to somewhere else in non-volatile memory, an area that would have enough space for the code to continue the initialization process. You would have to ask someone more familiar with CPU architecture why they use an indirect approach. My guess is that many CPU architectures define a vector table, which is a list of places the CPU will jump to when various contditions are met (e.g. an interrupt, or reset).
More seriously, at least for modern systems: the engineers who designed the computer created a memory map that defined which hardware can be found where. They simply ensured that the reset vector would point to an area of non-volatile memory that can be read directly (e.g. an EEPROM would work since you feed it an address and it returns data, much like RAM). That jump would be to somewhere else in non-volatile memory, an area that would have enough space for the code to continue the initialization process. You would have to ask someone more familiar with CPU architecture why they use an indirect approach. My guess is that many CPU architectures define a vector table, which is a list of places the CPU will jump to when various contditions are met (e.g. an interrupt, or reset).
Where do I read more about this?
Here's one source: https://depletionmode.com/uefi-boot.html
https://www.youtube.com/playlist?list=PLUFkSN0XLZ-ltETI20mpX...
The ost2.fyi courses are all high quality
The ost2.fyi courses are all high quality
In the page source:
<body>
<!-- Femboy Mode Button - Hidden on Mobile -->
<button class="rave-button" id="raveButton" title="Femboy Mode" style="display: none;">
<span class="button-text">uwu</span>
</button>
Really nice post, some months ago I also wrote about linux boot, but a bit more focused on the IO side (what's on disk, how is it loaded), here: https://blog.davidv.dev/posts/booting-x86-64/
Oh wow! Combined with the explaination of iso files which can be a single file which can have things like fat and bzimage and rootfs etc. with the bootloader and combined with software like dd / gnome-disks and your article and the HN thread article, this finally makes me understand how Linux starts and how we can install things from https / internet and use software to fundamentally change the operating system
Its magic.
I was recently trying to build my own linux operating system and I felt so frustrated as to how to build an iso image from bzImage / linux kernel + initramfs but I was able to withstand its pain somehow and it took me a week to actually learn a lot more about the fundamentals of linux which are so fascinating.
Now, I was trying to do some mix and matching (imagine tinycorelinux initramfs and buildroot bzImage and merging them) and doing some other shenanigans.
Sometimes my computer kernel didn't work or the userspace didn't work in the vm and I guess now WHEN I AM WRITING THIS POST, I realized that it was because of the difference in 32 bit and 64 bit, I think I had 64 bit kernel and 32 bit userspace which had some issues
There were some different things as well, which had caused some issues which made me want to scratch my remaining hair but it was so worth it (maybe i used some llm assistance in the end as well), its all just makes sense now, I always wanted to learn how computers work from scratch, now I feel like I have a very basic idea on how things work and they are complex indeed :sob:
I was looking for a post like yours yesterday and so I am still glad I found it when the topic is still fresh.
I faced so many issues trying to build my own iso but I don't know if it was my skill issue which streched it to a week. But the whole process of building your own iso seems less daunting to me now knowing what it really is
I may have skill issues indeed but I fixed those, I feel like that there is a lot to learn from those errors that I missed but maybe that's also because they got too overwhelming. But I now know a path which works and some explainations of why they work. I feel more confident in my ability to make my own custom distro even, but my appreciation for linux grows so much.
Its just such a massive rabbit hole and most of linux is literally just "it just works", linux is amazing.
Its magic.
I was recently trying to build my own linux operating system and I felt so frustrated as to how to build an iso image from bzImage / linux kernel + initramfs but I was able to withstand its pain somehow and it took me a week to actually learn a lot more about the fundamentals of linux which are so fascinating.
Now, I was trying to do some mix and matching (imagine tinycorelinux initramfs and buildroot bzImage and merging them) and doing some other shenanigans.
Sometimes my computer kernel didn't work or the userspace didn't work in the vm and I guess now WHEN I AM WRITING THIS POST, I realized that it was because of the difference in 32 bit and 64 bit, I think I had 64 bit kernel and 32 bit userspace which had some issues
There were some different things as well, which had caused some issues which made me want to scratch my remaining hair but it was so worth it (maybe i used some llm assistance in the end as well), its all just makes sense now, I always wanted to learn how computers work from scratch, now I feel like I have a very basic idea on how things work and they are complex indeed :sob:
I was looking for a post like yours yesterday and so I am still glad I found it when the topic is still fresh.
I faced so many issues trying to build my own iso but I don't know if it was my skill issue which streched it to a week. But the whole process of building your own iso seems less daunting to me now knowing what it really is
I may have skill issues indeed but I fixed those, I feel like that there is a lot to learn from those errors that I missed but maybe that's also because they got too overwhelming. But I now know a path which works and some explainations of why they work. I feel more confident in my ability to make my own custom distro even, but my appreciation for linux grows so much.
Its just such a massive rabbit hole and most of linux is literally just "it just works", linux is amazing.
I am curious were the differntiation comes between linux, and other unix systems (bsd, etc ..).
Thanks! Nice to see it has plenty of diagrams.
It's a weird article for me. On one side it is an interesting topic. On the other hand why are we explaining what a hex number is? Who is interested in this level of detail but doesn't know hex? Maybe I'm overanalyzing.
At the same time this doesn't address my biggest open question on the topic - how do we get from the physical push to the reset vector? Somehow that magic works in HW, physics and electronics - how?
At the same time this doesn't address my biggest open question on the topic - how do we get from the physical push to the reset vector? Somehow that magic works in HW, physics and electronics - how?
I think it’s an artifact of AI being used to write it.
I spotted a few more down the page and stopped reading.
I trust the judgment (and curation) of a person who invested significant time into learning stuff and then took even more time to write it down.
I don’t trust people who use AI to generate text.
If I want to read AI slop — I can generate one myself.
I want some soul in texts.
It is a sad day for the internet.
I spotted a few more down the page and stopped reading.
I trust the judgment (and curation) of a person who invested significant time into learning stuff and then took even more time to write it down.
I don’t trust people who use AI to generate text.
If I want to read AI slop — I can generate one myself.
I want some soul in texts.
It is a sad day for the internet.
HN is not just read by IT professionals. And they might be a bit curious about Linux startup without necessarily recalling what they know or never knew about hexadecimals.
It's fine to explain things to people that are not into that topic. But I also wonder what the target audience is. On one hand, he explains what a hexadecimal ist, but then jumps over essential information needed to understand the boot process. It's like: "Learning to swim: This is water, it is wet, if you jump in you sink and in water you cannot breath. Then you start moving your body parts and then you swim."
Articles like this make me wish i had enough points to downvode them into oblivion.
What a waste of time. I'm with the users that argue that if you need a "pretty please" explanation of what HEX values are, you shouldn't even begin to worry about the linux boot process.
What a waste of time. I'm with the users that argue that if you need a "pretty please" explanation of what HEX values are, you shouldn't even begin to worry about the linux boot process.
Does anyone have a similar article with more detail? I don't quite want to read the datasheet of your favorite microprocessor, but I would like a decent amount more detail than what's provided. Especially before UEFI/BIOS.
At a very high level, the processor initialization procedure is similar to most microcontrollers:
- processor is powered up with RESET pin asserted, making sure that all circuits are in a known-safe state.
- when RESET is deasserted, all autonomous circuits (e.g. core control units, cache controllers, ALUs) go through a hardware setup phase.
- the processor accesses the boot firmware according to the platform design. There's many options here, but the three most common are 1) the boot ROM is permanently mapped to a dedicated hardware address, and the processor uses its memory controller to access that memory; 2) the boot ROM is directly connected to the processor via dedicated I/O pins; 3) the initial boot code is located on the processor itself (factory-programmed EEPROM).
- if the boot ROM is not mapped to a memory address, the data is loaded into CPU cache (external RAM needs to be initialized first, and that task is usually performed by the firmware).
- the primary cpu core starts executing boot code (UEFI/BIOS/etc) from said predefined hardware address. Other cores (and processors) are usually left uninitialized throughout the startup process, and it is left to the operating system to bring up the remaining parts of the system.
Specifically for Intel, see https://binarydebt.wordpress.com/2018/10/06/how-does-an-x86-... . Or see https://electronics.stackexchange.com/a/726918 and its comments to get an idea of the differences between platforms.
- processor is powered up with RESET pin asserted, making sure that all circuits are in a known-safe state.
- when RESET is deasserted, all autonomous circuits (e.g. core control units, cache controllers, ALUs) go through a hardware setup phase.
- the processor accesses the boot firmware according to the platform design. There's many options here, but the three most common are 1) the boot ROM is permanently mapped to a dedicated hardware address, and the processor uses its memory controller to access that memory; 2) the boot ROM is directly connected to the processor via dedicated I/O pins; 3) the initial boot code is located on the processor itself (factory-programmed EEPROM).
- if the boot ROM is not mapped to a memory address, the data is loaded into CPU cache (external RAM needs to be initialized first, and that task is usually performed by the firmware).
- the primary cpu core starts executing boot code (UEFI/BIOS/etc) from said predefined hardware address. Other cores (and processors) are usually left uninitialized throughout the startup process, and it is left to the operating system to bring up the remaining parts of the system.
Specifically for Intel, see https://binarydebt.wordpress.com/2018/10/06/how-does-an-x86-... . Or see https://electronics.stackexchange.com/a/726918 and its comments to get an idea of the differences between platforms.
GRUB is mentioned but not detailed.
Here are some details: https://www.pixelbeat.org/docs/disk/
Here are some details: https://www.pixelbeat.org/docs/disk/
The topic is interesting but it seems to be targeted for my grandmother.
> When power stabilizes, the CPU resets itself to a tiny, old‑fashioned mode called real mode. Real mode dates back to the original 8086 chip. The rules are simple on purpose. Memory addresses are built from two values the CPU keeps in special fast storage called registers. You combine a segment and an offset like this:
physical_address = (segment << 4) + offset
I dont know, i just don't like the tone. This is a complex subject where the target audience should probably already know what is an hexadecimal number or an interrupt and the explanation of a cpu register ought to be better than:
"A register is a tiny slot inside the CPU. It holds a number the CPU is using right now."
If the subject interest you, you deserve better.
>A register is a tiny slot inside the CPU. It holds a number the CPU is using right now
What's your issue with this? Would you prefer it mentioned the x86 register doesn't always correspond to the same place in the register file?
What's your issue with this? Would you prefer it mentioned the x86 register doesn't always correspond to the same place in the register file?
There's nothing wrong with it but most people striving to do this would make each bit clickable to detail or something so that you can read at your level. I imagine this was a constraint of the site framework or the author's writing style.
But hey what the heck, it's fine. An LLM can rewrite it to whatever level of knowledge you like so the deepest level is optimal.
But hey what the heck, it's fine. An LLM can rewrite it to whatever level of knowledge you like so the deepest level is optimal.
Agreed. A lot of these articles leave me with more questions than answers.
These blog posts really annoy me because I feel like with 20% more effort you could have something worth reading.
These blog posts really annoy me because I feel like with 20% more effort you could have something worth reading.
I wonder if anyone will actually write their own article/blog providing a much better explanation of the subject matter. Or at least provide links to those articles that are alternatives to this.
The problem is that your 20% isn't the same 20% as anyone elses 20%.
If you want a more thorough explanation, go read a book. Many are available for free on sites such as archive.org and programming-motherfucker.com
If you want a more thorough explanation, go read a book. Many are available for free on sites such as archive.org and programming-motherfucker.com
One of the things we were taught in uni was audience analysis. I think about it a lot. What's expected to already be known? What acronyms or phrases need defining? Etc. This is an art I'm far from perfect at and it seems a lot of tech writers are too
Hard to read on my phone due to faded text.
The styling is bad on a desktop browser too. If you use Firefox or Firefox Mobile then reader mode is good for cases like this.
The self deprecatingly downvoted look.
fascinating how it's all over the place wrt level of detail. and absolutely unreadable. luckily the layout is simple and reader mode works.
> Hex is base 16
i would argue that someone that understand bases (in the first place), understands what the << operator does (context where base 16 is explained), but doesn't understand what base 16 is, doesn't exist. this is the kind of haphazard approach of this article i'm talking about. even the author's name, 0xkato, is an example of this.
as to the content, i wish it had touched on TPM, PCRs, UEFI secure boot, and ME pre-boot.
i'm forgiving all the actual errors since it is a pretty broad overview.
i'm guessing first-year uni student.
rather amazed a post like this can make it to the #1 spot.
> Hex is base 16
i would argue that someone that understand bases (in the first place), understands what the << operator does (context where base 16 is explained), but doesn't understand what base 16 is, doesn't exist. this is the kind of haphazard approach of this article i'm talking about. even the author's name, 0xkato, is an example of this.
as to the content, i wish it had touched on TPM, PCRs, UEFI secure boot, and ME pre-boot.
i'm forgiving all the actual errors since it is a pretty broad overview.
i'm guessing first-year uni student.
rather amazed a post like this can make it to the #1 spot.
Video device initialization is intimately intertwined and a dependency for all this early boot stuff. I was hoping to learn more but it's not even mentioned. Still, neat.
It's not a dependency for Linux boot at all. You can do well with serial port alone, as anyone who brought up eg. an ARM SoC in Linux will attest to.
Also it's not very interesting either. At simplest, Linux just needs to take a pointer to a beginning of a framebuffer and some metadata, and will write to the framebuffer whenever there's something to update.
Also it's not very interesting either. At simplest, Linux just needs to take a pointer to a beginning of a framebuffer and some metadata, and will write to the framebuffer whenever there's something to update.
If you would like to see an actually "interesting" boot, I recommend checking out how Raspberry Pi's boot.
It is a unique monstrosity that boots from the video / GPU core instead of one of the ARM cores. It has an arcane undocumented architecture.
It is a unique monstrosity that boots from the video / GPU core instead of one of the ARM cores. It has an arcane undocumented architecture.
When I realized that, after buying my first Rpi (2B), that was the last Rpi I ever bought. :)
Thankfully, pretty much everyone else just uses U-Boot.
Thankfully, pretty much everyone else just uses U-Boot.
Maybe not linux specifically, but POST requires a video device software (BIOS Option ROM or UEFI GOP Drivers) of some sort does it not? That's been my experience with all PCs for 30 years. But maybe there are cases where it doesn't?
edit: Apparently it's a desktop motherboard firmware thing. Ubiquitous but not technically a requirement for POSTing a computer.
edit: Apparently it's a desktop motherboard firmware thing. Ubiquitous but not technically a requirement for POSTing a computer.
I've found AM4/AM5 boards will still boot Linux without a discrete or integrated GPU, running a GPUless CPU, not an APU.
It was sorta required by IBM PC compatibles, but is not required by UEFI which supports serial console (or other interfaces).
IBM PC assumed existence of graphic output and sometimes Option ROMs did really too crazy things with it, I still have shivers when I hear "intel raid card" because of that one with possibly Win3.x in ROM...
IBM PC assumed existence of graphic output and sometimes Option ROMs did really too crazy things with it, I still have shivers when I hear "intel raid card" because of that one with possibly Win3.x in ROM...
Soekris (rip) had an x86 network device. Four 10/100s and the disk was a CF. Could only serial console that thing - or SSH once it's running. Best router I ever had.
Also, in 2000 when Windows crashed you could get a serial debugger. Wonder if they still do that?
Also, in 2000 when Windows crashed you could get a serial debugger. Wonder if they still do that?
People still need to do driver ddvelopement. So you can still set up a Windows PC to expose kernel debug interface over serial port: https://learn.microsoft.com/en-us/windows-hardware/drivers/d...
If you can find a copy of this on the high seas, it's a great resource. I wrote my own OS by starting with this and the Linux source in the mid-90s:
https://www.amazon.com/-/he/Developing-32-Bit-Operating-Syst...
https://www.amazon.com/-/he/Developing-32-Bit-Operating-Syst...
Only on IBM PC because it essentially always assumed presence of either MDA or CGA, and over time evolved to assume presence of VGA.
UEFI does not require at all and supports and UI framework to enable work in both graphical and textual (with so-called VT-UTF8) mode.
UEFI does not require at all and supports and UI framework to enable work in both graphical and textual (with so-called VT-UTF8) mode.
It's because on a brief period of old PC hardware (1994-1998), when Linux was starting off, high-resolution video initialization (SVGA+) was easier to do in 16-bit mode, before the bootloader switched the CPU over to 32-bit mode. Because GRUB handled this transition, GRUB became responsible for video initialization. After 1998 GPU manufacturers added 32-bit support for initialization, but the long tail of users with hardware with that limitation really entrenched this responsibility in GRUB.
Seems like there are many useful suggestions for the author. Here is mine: maybe an interactive style would work much better for educational content.
There is a well praised post on HN: https://www.nan.fyi/database, built with the framework: https://github.com/nandanmen/NotANumber
There is a well praised post on HN: https://www.nan.fyi/database, built with the framework: https://github.com/nandanmen/NotANumber
As should be clear from the reset vector, the 80286 and its successors actually boot in unreal mode. On the 80386, the base address of the code segment is 0xffff0000, which cannot be obtained by shifting the 16-bit CS register by 4. The descriptor cache simply gets loaded with the correct value at reset. Writing to CS in real mode overwrites the cached value with CS * 16.
This isn't quite right either. That's not what unreal mode is. Unreal mode has 32-bit data segments limit, not code segment limits.
In this case the code segment still has a 16 bit limit, it's just that its base address in the descriptor cache is outside the bounds typically associated with real mode.
In this case the code segment still has a 16 bit limit, it's just that its base address in the descriptor cache is outside the bounds typically associated with real mode.
Reading this just reinforces how much of the x86/Linux boot chain is fossilized ceremony glued together for backward compatibility.
Kinda missing the point of UEFI if you don't mention that it skips the first 3 sections and allows your kernel to boot directly from 64-bit mode ("long mode") with paging, a framebuffer, and a function to read files from your boot drive, already set up for you. Removes the need for GRUB entirely.
This. I haven't seen or touched GRUB or BIOS in about a decade.
I wonder whether the power button really directly starts the CPU. I wouldn't be surprised if the Intel Management Engine (or AMD equivalent), a CPU that's running all the time, is what gets the power button signal and starts the CPU.
I think that is the job of the embedded controller, which is before the bootloader bringing up CPU. On Chromebooks, that part is open source along with the coreboot bootloader.
https://chromium.googlesource.com/chromiumos/platform/ec/+/H...
https://chromium.googlesource.com/chromiumos/platform/ec/+/H...
Light gray text on white??
Related to this topic, what is the best way to replace the code involved in the entire boot process? This is useful when sanitizing a system received from a provider that may not be trustworthy, as malware could be hidden at low levels.
The disk could be wiped from the BIOS. One could also run “fwupdmgr update” from a live USB to update the motherboard firmware and then reinstall the operating system. However, I’m not sure if this would completely clear the system.
The disk could be wiped from the BIOS. One could also run “fwupdmgr update” from a live USB to update the motherboard firmware and then reinstall the operating system. However, I’m not sure if this would completely clear the system.
I'm a bit late to comment on this, but people might find it interesting. The title is "programming in assembly without an operating system", but it gives really good insight to how the early boot process works, and how to begin interacting with it.
Thank you to the author:
https://www.youtube.com/watch?v=ZFHnbozz7b4
Thank you to the author:
https://www.youtube.com/watch?v=ZFHnbozz7b4
This doesn't cover the things that the CPU secretly does before it finally enters Real Mode, such as loading and validating the microcode.
Based on all the negative comments, and being a non-expert, I had an LLM generate an article for that same title. I suspect it was more approachable and more technically accurate than this. In fact I asked it to compare its article with this one and the negative comments.
The author of any technical blog post should be using an LLM to vet things before posting to find gaps or inconsistencies.
The author of any technical blog post should be using an LLM to vet things before posting to find gaps or inconsistencies.
ARM and lots of non-x86 architectures often use a series of bootloaders to kick up ram, wake up parts of the hardware, blah blah, and read devicetree blobs to know what the hardware looks like
I'm going to save this guys blog in one step
https://webaim.org/resources/contrastchecker/
(this is the site: https://webaim.org/resources/contrastchecker/?fcolor=D0D0D0&...)
https://webaim.org/resources/contrastchecker/
(this is the site: https://webaim.org/resources/contrastchecker/?fcolor=D0D0D0&...)
Thanks for the detailed write-up! I'd love to see something like this for ARM too!
This post made me remember the technical interview by phone I had with Facebook circa 2010 for a Production Engineer role (but maybe it wasn't called yet that way back then) where they asked me exactly this. Well, they actually asked "explain me the boot process of a Linux server", with no more hints and "go into the details you feel are important" as the only help.
Anyway I should have moved to Dublin and something something surveillance capitalism so the grape wasn't ripe enough anyway.
Anyway I should have moved to Dublin and something something surveillance capitalism so the grape wasn't ripe enough anyway.
Nice to see the good old hacker energy & independent blogs explaining things showing up on top of hacker news. Welcome change from insufferable agent this and vibe that
Funny how those three posts are in hacker news top 5 now.
I guess today is the low level appreciation day.
* The Linux Boot Process: From Power Button to Kernel
* The Journey Before main()
* How programs get run: ELF binaries (2015) (lwn.net)
Very much overdue, i would say! Lately HN was turning into just adware for AI news.
Does anybody have pointers to similar low-level details specific to iOS/Android systems? Given that most of us by now have a few of these lying around the house gathering dust, they can make a nice DUT to hack/study/learn a few technical things. I would be quite interested in knowing more about how the RF subsystem works and maybe repurposed as an SDR for example.
Does anybody have pointers to similar low-level details specific to iOS/Android systems? Given that most of us by now have a few of these lying around the house gathering dust, they can make a nice DUT to hack/study/learn a few technical things. I would be quite interested in knowing more about how the RF subsystem works and maybe repurposed as an SDR for example.
Agreed, a very refreshing change.
I cant reccomend anything apple or android based, but the PinePhone has some reasonable low-level documentation on itś SoC (Allwinner A64). And there are a great series of tutorials of how Apache Nuttx was ported to the PP. Here's one of the earlier ones: https://lupyuen.org/articles/uboot
I've been working through them myself but still dont understand the boot process, and a long way from radio chip functionality. But I suspect you'll find radio chips quite locked down, since they are licensed for connection to mobile networks. Often there is just a unknown binary blob running the show.
I cant reccomend anything apple or android based, but the PinePhone has some reasonable low-level documentation on itś SoC (Allwinner A64). And there are a great series of tutorials of how Apache Nuttx was ported to the PP. Here's one of the earlier ones: https://lupyuen.org/articles/uboot
I've been working through them myself but still dont understand the boot process, and a long way from radio chip functionality. But I suspect you'll find radio chips quite locked down, since they are licensed for connection to mobile networks. Often there is just a unknown binary blob running the show.
Nice, thank you.
My introduction to this subject was through Harald Welte's work on OpenMoko (i still have an old one lying around somewhere) but after the explosion of iPhones/Android phones have not kept apace. Here is Harald's old but still informative presentation Anatomy of smartphone hardware: Dissecting contemporary cellphone hardware - https://media.ccc.de/v/25c3-3008-en-anatomy_of_smartphone_ha...
Also you might find Roger Ye's old book Embedded Programming with Android: Bringing Up an Android System from Scratch pretty useful.
My introduction to this subject was through Harald Welte's work on OpenMoko (i still have an old one lying around somewhere) but after the explosion of iPhones/Android phones have not kept apace. Here is Harald's old but still informative presentation Anatomy of smartphone hardware: Dissecting contemporary cellphone hardware - https://media.ccc.de/v/25c3-3008-en-anatomy_of_smartphone_ha...
Also you might find Roger Ye's old book Embedded Programming with Android: Bringing Up an Android System from Scratch pretty useful.
Oh hey, a fellow noticing person!
yes, and the bar is not at all at the same level.
weekend hackernews best hackernews
kgasser88(1)
This post skips all the interesting things in the modern firmware dance. Not the least of which is when you call ExitBootServices() you're already in long mode. There's no need for the journey through real and protected.